有許多類型的模型，其中常見的就是工業模型。認識的朋友都知道，工業模型制作，是打磨。磨料加工有很多地方需要注意，要講究經驗和技巧。裝配模型時，模型表面會出現大量的裂縫，嚴重影響模型的外觀，因此必須對模型縫隙進行修補，主要工具是填充、抹布和砂紙。
There are many types of models, the most common of which is the industrial model. Friends know that the first step in making industrial models is polishing. There are many places to pay attention to in abrasive machining. We should pay attention to experience and skills. When assembling the model, a large number of cracks will appear on the model surface, which will seriously affect the appearance of the model. Therefore, the model cracks must be repaired. The main tools are filling, rag and sandpaper.
另外，還應注意，工業模型在組合時必須粘結，否則接縫容易斷裂。土又名有機樹脂，專門用來填充模型間的空隙。也有許多類型適用于許多大的模型庫。在使用時，用合適的工具在要填充的關節線或槽處施加適當?shù)牧?。在施工過程中，施加一定的壓力填充凹角。土體成分含有可溶解的塑料溶液，因此當它接觸模型表面時很難脫落。但由于溶液會揮發，所以在完全干燥和硬化的時候，體積會稍微收縮。在補土的時候，我們必須補一點，使土壤有足夠的體積，以滿足磨削需要。
In addition, it should also be noted that the industrial model must be bonded during combination, otherwise the joint is easy to break. Soil, also known as organic resin, is specially used to fill the gaps between models. There are also many types that apply to many large model libraries. When in use, use a suitable tool to apply an appropriate amount at the joint line or groove to be filled. During construction, a certain pressure shall be applied to fill the concave corners. The soil component contains soluble plastic solution, so it is difficult to fall off when it contacts the surface of the model. However, due to the volatilization of the solution, the volume will shrink slightly when it is completely dried and hardened. When replenishing the soil, we must replenish a little to make the soil have enough volume to meet the grinding needs.
工業模型制作拋光后，你可以對它著色。你可以用你的手或者噴筆。手涂涂料的優點是能在某些精細區域使用，但大面積使用時容易產生筆痕。用噴槍在較大的區域內噴涂非常均勻。油層比較薄，起到的作用更好。但在小一點的地方使用分色紙比較麻煩。
After the industrial model is made and polished, you can color it. You can use your hand or fountain pen. The advantage of hand coating is that it can be used in some fine areas, but it is easy to produce pen marks when used in a large area. Spray evenly over a large area with a spray gun. The oil layer is relatively thin and plays a better role. But it is more troublesome to use color separation paper in smaller places.
工業模型不像手工模式那么簡單，它已經從數碼產品、家用醫療產品和汽車零部件轉變?yōu)榇笮蜋C械模式和工程模式。比建筑模型大得多，而且工藝難度因素也有進一步提高。
Industrial model is not as simple as manual model. It has changed from digital products, household medical products and auto parts to large-scale mechanical model and engineering model. It is much larger than the building model, and the process difficulty factors have been further improved.
1.盡量把工業模型放在通風干凈的房間里，以免受潮和陽光直接照射。室溫不超過35℃，相對濕度不超過30%-80%，否則易發生工業模型脫膠變形。工業模型不能直接暴露于陽光下，更不要說在陽光下暴曬。
1. Try to put the industrial model in a well ventilated room to avoid moisture and direct sunlight. The room temperature shall not exceed 35 ℃, and the relative humidity shall not exceed 30% - 80%, otherwise the degumming deformation of the industrial model is easy to occur. Industrial models cannot be directly exposed to the sun, let alone exposed to the sun.
2.工業模型宜看不宜接觸，尤其在市場營銷展示時，應采取相應措施。裝飾物，綠樹等小配件如有脫落，應妥善保管，并允許模型制造公司的維修人員及售后服務人員稍后再安裝。
2. The industrial model should be seen rather than contacted, especially when displayed in the marketing center, corresponding measures should be taken. If small accessories such as decorations and green trees fall off, they shall be kept properly, and professional maintenance personnel and after-sales service personnel of the model manufacturing company are allowed to install them later.
3.燈光應每兩小時關燈一次，不要長時間關燈。假如真有沙盤式噴泉，它應該經常檢查有沒有水(因為水在不斷蒸發)。水不夠用時應及時補充。如果發現噴泉不噴水，應立即關閉電源，以免造成損壞。
3. The light should be turned off every two hours, not for a long time. If there is a sand table fountain, it should always check whether there is water (because the water is evaporating). When the water is not enough, it shall be replenished in time. If it is found that the fountain does not spray water, turn off the power immediately to avoid damage.
以上就是小編為大家介紹的工業模型維護的全部內容，看完文章的你應該有所了解了。
The above is the whole content of industrial model maintenance introduced by Xiaobian. You should know something after reading the article.
The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: large tank model http://m.maov.com.cn
